We've uncovered this article about How to Install a Bathtub Yourself down the page on the internet and believe it made sense to write about it with you on my blog.

Mounting a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a moderately challenging job. If the old tub is conveniently accessible, the task can move rapidly; if you have to open a wall to eliminate the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will need an assistant to leave the old tub and embeded in the new one. Make sure you have qualified on your own for the task and fit trying it. As opposed to employing a contractor to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This post will certainly assist you set up a brand-new bathtub in your bathroom if you have actually currently acquired a new bathtub and also don't need to change the plan of your previous supply of water pipelines.
Your devices and also product list should consist of the following:
Preparing for the Setup
To start with, the sustaining framework provided with the bathroom must be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to avoid stress on the tub.
Fit the adaptable tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be fitted in its final position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be rather troublesome as a result of the limited gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Making use of the two wood boards under its feet, put the bathtub in the called for position. The wood boards are helpful in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub up until the spirit level reviews degree.
To mount taps, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; then do the same for the various other tap.
Turn on the water and also inspect all joints as well as new pipework for leakages and also tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet and the regular outlet for leakages.
Ultimately, fix the bath paneling as defined in the maker's user's manual. Tiling and sealing around the bath tub ought to wait till the tub has actually been utilized at the very least once as this will certainly resolve it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Protect the tap in position with the maker offered backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type should be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to break a rigid seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in problems with dampness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealer can split relatively very early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I found that blog entry on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while perusing the web. Sharing is nice. One never knows, you might be helping someone out. Thank-you for your time spent reading it.
Need it done? Dial!